Description
Features
Hole for Grease Fitting
![Bushing [6805150] (Press-In/Weld-On) for Lower Tilt Cylinder | Bobcat® Bob-Tach - Image 2](https://rivervalleymachineusa.com/wp-content/uploads/2019/09/6805150_Angle.png)
![Bushing [6805150] (Press-In/Weld-On) for Lower Tilt Cylinder | Bobcat® Bob-Tach - Image 3](https://rivervalleymachineusa.com/wp-content/uploads/2019/09/6805150_Angle-T.png)
![Bushing [6805150] (Press-In/Weld-On) for Lower Tilt Cylinder | Bobcat® Bob-Tach - Image 4](https://rivervalleymachineusa.com/wp-content/uploads/2019/09/6805150_Angle-V.png)
Bushing [6805150] (Press-In/Weld-On) for Lower Tilt Cylinder | Bobcat® Bob-Tach
In stock (can be backordered)
$19.49
Bushing [6805150] (Press-In/Weld-On) for Lower Tilt Cylinder | Bobcat® Bob-Tach
REPLACEMENT for BOBCAT® PART #: 6800227
COMPATIBLE w/ BOBCAT® PART #: 6589665
Bushing for Tilt Cylinder Rod End.
$19.49
Additional information
Contact River Valley Machine
Questions, Comments?
You may also like…
-
Bushing [6589665] (Press-In/Weld-On) | Bobcat® Bob-Tach
$19.95 Add to cartBushing [6589665] (Press-In/Weld-On) | Bobcat® Bob-Tach
Bushing [6589665] (Press-In / Weld-On) | Bobcat® Bob-Tach
COMPATIBLE w/ BOBCAT PART #: 6805150
This bushing is press-fit into your Bob-Tach. These wear out over time causing a lot of play in your Bob-Tach. These are hardened bushings and can easily be removed with a torch or air arc. This will greatly reduce the time needed to remove the old bushings.
Replacing these Bushings is required and will keep your machine operating like new. In certain cases of excessive wear these can be welded in as well.
$19.95
Related products
-
RVM® Pallet Fork w/ Walk-Thru
$995.00 Call RVM to OrderRVM® Pallet Fork w/ Walk-Thru
River Valley Machine Pallet Fork w/ Walk-Thru for Skid-Steer Loader
- 48″ Tines
- Fully Adjustable
- Rated for 4,500 lbs
$995.00 -
Bushing [6717259] (Weld-On) for Bobcat® Bob-Tach
$25.95 Add to cartBushing [6717259] (Weld-On) for Bobcat® Bob-Tach
Bushing [6717259] (Weld-On) for Bobcat® Bob-Tach
This bushing is welded into your Bob-Tach. The bushings eventually wear out causing a lot of play in your Bob-Tach. Replacing these weld-on bushings is a lot cheaper than buying a new Bob-Tach.
$25.95 -
![Pivot Pin (SOLID) [6716601] for Lower Tilt Cylinder | Bobcat® Bob-Tach](https://rivervalleymachineusa.com/wp-content/uploads/2019/05/6716601-324x324.png)
Pivot Pin (SOLID) [6716601] for Lower Tilt Cylinder | Bobcat® Bob-Tach
$29.95 Add to cartPivot Pin (SOLID) [6716601] for Lower Tilt Cylinder | Bobcat® Bob-Tach
Pivot Pin [6716601] for Lower Tilt Cylinder | Bobcat® Bob-Tach
This Pivot Pin is used between the Lower Tilt Cylinder and your Bobcat® Bob-Tach.
This is a solid pivot pin – the pin does not have a grease zerk hole.
$29.95
