Description
Dimensions
3″ OD w/ Tapered Hole
5.125″ Length
For Use With:
1.75″ Diameter Pin [6729358]
![Bushing [6728999] (Weld-On) for Loader Lift Arm Boom | Bobcat® - Image 2](https://rivervalleymachineusa.com/wp-content/uploads/2019/08/6728999_Angle-R.png)
![Bushing [6728999] (Weld-On) for Loader Lift Arm Boom | Bobcat® - Image 3](https://rivervalleymachineusa.com/wp-content/uploads/2019/03/6728999_Diagram.jpg)
Bushing [6728999] (Weld-On) for Loader Lift Arm Boom | Bobcat®
Only 12 left in stock (can be backordered)
$92.95
Bushing [6728999] (Weld-On) for Loader Lift Arm Boom | Bobcat®
This bushing comes welded into the Tapered Pivot Pin locations on your Loader’s Lift Arm. The holes are tapered internally for the holes in the Bob-Tach attachment mounting system to help reduce vibration. However, the tapered holes simply wear out over time not allowing for the Pivot Pins to stay tight.
Replacing these bushings is a whole lot less expensive than buying a new Loader Arm Assembly!
$92.95
| Dimensions | 5.125 × 3 in |
|---|---|
| Bobcat | Bobcat A300 (All-Wheel Steer), Bobcat S220, Bobcat S250, Bobcat S300, Bobcat S330, Bobcat T250, Bobcat T300, Bobcat T320 |
Additional information
| Dimensions | 5.125 × 3 in |
|---|---|
| Bobcat | Bobcat A300 (All-Wheel Steer), Bobcat S220, Bobcat S250, Bobcat S300, Bobcat S330, Bobcat T250, Bobcat T300, Bobcat T320 |
Contact River Valley Machine
Questions, Comments?
Related products
-
RVM® Pallet Fork w/ Walk-Thru
$995.00 Call RVM to OrderRVM® Pallet Fork w/ Walk-Thru
River Valley Machine Pallet Fork w/ Walk-Thru for Skid-Steer Loader
- 48″ Tines
- Fully Adjustable
- Rated for 4,500 lbs
$995.00 -
![Compression Spring (Short) [6704453] for Quick-Attach Handle | Bobcat® Bob-Tach](https://rivervalleymachineusa.com/wp-content/uploads/2019/02/6704453_RVM-324x324.png)
Compression Spring (Short) [6704453] for Quick-Attach Handle | Bobcat® Bob-Tach
$8.95 Add to cartCompression Spring (Short) [6704453] for Quick-Attach Handle | Bobcat® Bob-Tach
Compression Spring (Short) [6704453] for Quick-Attach Handle | Bobcat® Bob-Tach
The Handle Spring keeps the handles in the ‘up’ position and keeps the handles tight. Replacing the Handle Springs will help make your Bob-Tach operate like new.
IMPORTANT NOTE: Bobcat uses two (2) different handle springs. One is long, one is short. This is the short one with only 3 coil windings.
$8.95 -
![RVM® Repair Panel for Mount Plate [7143508-RH] (3 Pieces) | Bobcat® Bob-Tach](https://rivervalleymachineusa.com/wp-content/uploads/2019/03/7143508-RH_RVM-Kit-324x324.png)
RVM® Repair Panel for Mount Plate [7143508-RH] (3 Pieces) | Bobcat® Bob-Tach
$89.99 Add to cartRVM® Repair Panel for Mount Plate [7143508-RH] (3 Pieces) | Bobcat® Bob-Tach
RVM® Repair Panel for Mount Plate [7143508-RH] (3 Pieces) | Bobcat® Bob-Tach
A common failure of a Bobcat® Bob-Tach is the top portion of the Bob-Tach. OEM Material thickness is only ¼” – they simply wear thin, bend and eventually break over time. When this happens your attachments will fit loosely or fall off of your machine.
With this Repair Panel Plate Kit from River Valley Machine, you can replace these portions of your Bob-Tach to help make it appear & operate like new again, without spending $1300+ buying a new Bob-Tach.
When sitting inside your machine, this is for the Right Side panel.
$89.99
