Description
Dimensions
1.55″ ID
3″ OD
For Use With:
1.50″ OD Pin
![Bushing [7140168] (Weld-On) for Bobcat® Bob-Tach](https://rivervalleymachineusa.com/wp-content/uploads/2019/09/7140168.png)
![Bushing [7140168] (Weld-On) for Bobcat® Bob-Tach - Image 2](https://rivervalleymachineusa.com/wp-content/uploads/2019/09/7140168_Diagram.png)
![Bushing [7140168] (Weld-On) for Bobcat® Bob-Tach - Image 3](https://rivervalleymachineusa.com/wp-content/uploads/2019/09/7140168_Diagram_FULL.png)
Bushing [7140168] (Weld-On) for Bobcat® Bob-Tach
In stock (can be backordered)
$54.95
Bushing (Weld-On) [7140168] | Bobcat® Bob-Tach
This bushing is welded into your Bob-Tach®. The bushings simply wear out over time causing issues with your attachment.
Replacing your bushings is a whole lot less expensive than buying a new Bob-Tach! These are hardened bushings and can easily be removed with an air arch or torch – this will greatly reduce the time needed to remove the old bushings.
$54.95
| Dimensions | 3 in |
|---|---|
| Bobcat |
Additional information
| Dimensions | 3 in |
|---|---|
| Bobcat |
Contact River Valley Machine
Questions, Comments?
Related products
-
Pivot Pin (Tapered) [7101078] w/ Bolt for Loader Arms / Lower Bob-Tach | Bobcat®
$25.95 Add to cartPivot Pin (Tapered) [7101078] w/ Bolt for Loader Arms / Lower Bob-Tach | Bobcat®
Pivot Pin (Tapered) [7101078] for Loader Arms / Lower Bob-Tach | Bobcat®
REPLACEMENT for BOBCAT PART #: 6734661
This Pivot Pin is used between your Skid-Steer’s Loader Arms and the Bob-Tach… These pins simply wear out over time causing a lot of play in your Bob-Tach.
Replacing your pins can help make your Bobcat operate like new again!
Bolt Included with your order!
River Valley Machine will include 5/8″ Hex Bolt Grade 8
$25.95 -
![Access Cover Plates (Squared) [7240780] for Clean-Out | Bobcat®](https://rivervalleymachineusa.com/wp-content/uploads/2019/08/7240780-324x324.png)
Access Cover Plates (Squared) [7240780] for Clean-Out | Bobcat®
$24.95 Add to cartAccess Cover Plates (Squared) [7240780] for Clean-Out | Bobcat®
Access Cover Plates [7240780] for Clean-Out | Bobcat®
REPLACEMENT FOR BOBCAT PART #: 6716010
Access Cover located on the loader’s drivetrain frames for easy access to the hydrostatic drive motor or to the track loader front idler.
These Clean-Out Plates are for use on machines using a 6.25″ x 5″ bolt pattern. Please check your bolt pattern prior to ordering.
Included w/ Kit:
1 Pair Access Cover Clean-Out Plates w / 4 Bolts
$24.95 -
![Compression Spring (Short) [6704453] for Quick-Attach Handle | Bobcat® Bob-Tach](https://rivervalleymachineusa.com/wp-content/uploads/2019/02/6704453_RVM-324x324.png)
Compression Spring (Short) [6704453] for Quick-Attach Handle | Bobcat® Bob-Tach
$8.95 Add to cartCompression Spring (Short) [6704453] for Quick-Attach Handle | Bobcat® Bob-Tach
Compression Spring (Short) [6704453] for Quick-Attach Handle | Bobcat® Bob-Tach
The Handle Spring keeps the handles in the ‘up’ position and keeps the handles tight. Replacing the Handle Springs will help make your Bob-Tach operate like new.
IMPORTANT NOTE: Bobcat uses two (2) different handle springs. One is long, one is short. This is the short one with only 3 coil windings.
$8.95
![Bushing [7140168] (Weld-On) for Bobcat® Bob-Tach](https://rivervalleymachineusa.com/wp-content/uploads/2019/09/7140168-324x324.png)