![Pivot Pin (Tapered) [7101078] w/ Bolt for Loader Arms / Lower Bob-Tach | Bobcat® - Image 2](https://rivervalleymachineusa.com/wp-content/uploads/2019/09/7101078_Angle-B.png)
![Pivot Pin (Tapered) [7101078] w/ Bolt for Loader Arms / Lower Bob-Tach | Bobcat® - Image 3](https://rivervalleymachineusa.com/wp-content/uploads/2019/09/7101078_Angle-A.png)
![Pivot Pin (Tapered) [7101078] w/ Bolt for Loader Arms / Lower Bob-Tach | Bobcat® - Image 4](https://rivervalleymachineusa.com/wp-content/uploads/2019/09/7101078_Angle-T.png)
![Pivot Pin (Tapered) [7101078] w/ Bolt for Loader Arms / Lower Bob-Tach | Bobcat® - Image 5](https://rivervalleymachineusa.com/wp-content/uploads/2019/09/7101078_Angle-S.png)
![Pivot Pin (Tapered) [7101078] w/ Bolt for Loader Arms / Lower Bob-Tach | Bobcat® - Image 6](https://rivervalleymachineusa.com/wp-content/uploads/2019/09/7101078_Angle-U.png)
![Pivot Pin (Tapered) [7101078] w/ Bolt for Loader Arms / Lower Bob-Tach | Bobcat® - Image 7](https://rivervalleymachineusa.com/wp-content/uploads/2019/09/7101078_OLD.png)
![Pivot Pin (Tapered) [7101078] w/ Bolt for Loader Arms / Lower Bob-Tach | Bobcat® - Image 8](https://rivervalleymachineusa.com/wp-content/uploads/2019/04/7101078_Diagram.jpg)
![Pivot Pin (Tapered) [7101078] w/ Bolt for Loader Arms / Lower Bob-Tach | Bobcat® - Image 9](https://rivervalleymachineusa.com/wp-content/uploads/2019/01/RVM_7101078.png)
Only 6 left in stock
$25.95
This Pivot Pin is used between your Skid-Steer’s Loader Arms and the Bob-Tach… These pins simply wear out over time causing a lot of play in your Bob-Tach.
Replacing your pins can help make your Bobcat operate like new again!
River Valley Machine will include 5/8″ Hex Bolt Grade 8
$25.95
| Weight | 1.21875 lbs |
|---|---|
| Dimensions | 4.05 × 1.5 in |
| Bobcat | Bobcat 773, Bobcat S100, Bobcat S130, Bobcat S150, Bobcat S160, Bobcat S175, Bobcat S185, Bobcat S205, Bobcat S450, Bobcat T110, Bobcat T140, Bobcat T180, Bobcat T190, Bobcat T450 |
1.5″ Diameter
4.05″ Length
5/8-11″ Inside Thread
| Weight | 1.21875 lbs |
|---|---|
| Dimensions | 4.05 × 1.5 in |
| Bobcat | Bobcat 773, Bobcat S100, Bobcat S130, Bobcat S150, Bobcat S160, Bobcat S175, Bobcat S185, Bobcat S205, Bobcat S450, Bobcat T110, Bobcat T140, Bobcat T180, Bobcat T190, Bobcat T450 |
This bushing is welded into your loader arm tapered pivot pin locations. The tapered holes wear out over time, not allowing for the tapered pivot pins to stay tight.
Replacing these bushings is a lot cheaper than buying a new Loader Arm Assembly.
This bushing is welded into your loader arm / boom tapered pivot pin locations. The tapered holes wear out over time, not allowing for the tapered pivot pins to stay tight.
Replacing these bushings is a lot cheaper than buying a new Loader Arm Assembly.
This Bushing is press-fit into your Bob-Tach. Bushings simply wear out over time causing a lot of play in your Bob-Tach. Replacing these bushings is sometimes required, and can help keep your machine operating like new.
* In certain cases of excessive wear these can be welded in as well.
![RVM® Wedge Repair Kit [LH] | Bobcat® Bob-Tach](https://rivervalleymachineusa.com/wp-content/uploads/2019/01/Bobcat-Bob-Tach-Wedge-Repair-Kit_RH-324x324.jpg)
River Valley Machine, LLC sells both Left and Right Wedge Repair Kits…
![Compression Spring (Short) [6704453] for Quick-Attach Handle | Bobcat® Bob-Tach](https://rivervalleymachineusa.com/wp-content/uploads/2019/02/6704453_RVM-324x324.png)
The Handle Spring keeps the handles in the ‘up’ position and keeps the handles tight. Replacing the Handle Springs will help make your Bob-Tach operate like new.
IMPORTANT NOTE: Bobcat uses two (2) different handle springs. One is long, one is short. This is the short one with only 3 coil windings.
