![Bushing [6805453] (Press-In/Weld-On) for Tilt Cylinder Rod | Bobcat® Bob-Tach - Image 2](https://rivervalleymachineusa.com/wp-content/uploads/2019/08/6805453_Angle-L.png)
![Bushing [6805453] (Press-In/Weld-On) for Tilt Cylinder Rod | Bobcat® Bob-Tach - Image 3](https://rivervalleymachineusa.com/wp-content/uploads/2019/08/6805453_Angle-R.png)
![Bushing [6805453] (Press-In/Weld-On) for Tilt Cylinder Rod | Bobcat® Bob-Tach - Image 4](https://rivervalleymachineusa.com/wp-content/uploads/2019/08/6805453_Angle-V.png)
![Bushing [6805453] (Press-In/Weld-On) for Tilt Cylinder Rod | Bobcat® Bob-Tach - Image 5](https://rivervalleymachineusa.com/wp-content/uploads/2019/02/6805453_Diagram.png)
Only 5 left in stock (can be backordered)
$18.95
This bushing is press-fit into Tilt Cylinder Rod Ends. In certain cases of excessive wear these can be welded in as well. Bushings simply wear out over time causing a lot of play in your Bob-Tach. Replacing these Bushings is required and will keep your machine operating like new.
These are hardened bushings and can easily be removed with a torch or air arc. This will greatly reduce the time needed to remove the old bushings.
$18.95
| Dimensions | 1.625 × 1.44 in |
|---|---|
| Bobcat | Bobcat 773, Bobcat A300 (All-Wheel Steer), Bobcat S150, Bobcat S160, Bobcat S175, Bobcat S185, Bobcat S205, Bobcat S220, Bobcat S250, Bobcat S300, Bobcat S330, Bobcat S450, Bobcat S510, Bobcat S530, Bobcat S550, Bobcat S570, Bobcat S590, Bobcat S595, Bobcat T180, Bobcat T190, Bobcat T250, Bobcat T300, Bobcat T320, Bobcat T450, Bobcat T550, Bobcat T590 |
1.25″ ID
1.438″ OD
1.625″ Long
1.25″ ID Pin
| Dimensions | 1.625 × 1.44 in |
|---|---|
| Bobcat | Bobcat 773, Bobcat A300 (All-Wheel Steer), Bobcat S150, Bobcat S160, Bobcat S175, Bobcat S185, Bobcat S205, Bobcat S220, Bobcat S250, Bobcat S300, Bobcat S330, Bobcat S450, Bobcat S510, Bobcat S530, Bobcat S550, Bobcat S570, Bobcat S590, Bobcat S595, Bobcat T180, Bobcat T190, Bobcat T250, Bobcat T300, Bobcat T320, Bobcat T450, Bobcat T550, Bobcat T590 |
![RVM® Wedge Repair Kit [RH] | Bobcat® Bob-Tach](https://rivervalleymachineusa.com/wp-content/uploads/2019/01/Bobcat-Bob-Tach-Wedge-Repair-Kit_RH-324x324.jpg)
River Valley Machine, LLC sells both Left and Right Wedge Repair Kits…
![Pivot Pin [6705223] w/ Zerk for Lower Tilt Cylinder | Bobcat® Bob-Tach](https://rivervalleymachineusa.com/wp-content/uploads/2019/05/6705223-324x324.png)
This Pivot Pin is used between your Bobcat® Bob-Tach and the Lower Tilt Cylinder.
This Pin features a grease zerk hole.
![Access Cover Plates (Squared) [7240780] for Clean-Out | Bobcat®](https://rivervalleymachineusa.com/wp-content/uploads/2019/08/7240780-324x324.png)
Access Cover located on the loader’s drivetrain frames for easy access to the hydrostatic drive motor or to the track loader front idler.
These Clean-Out Plates are for use on machines using a 6.25″ x 5″ bolt pattern. Please check your bolt pattern prior to ordering.
1 Pair Access Cover Clean-Out Plates w / 4 Bolts
